Long Victorian Style Women’s Vest

Hello!  Can you believe it’s the middle of September already?  Crazy.

I made a long Victorian style women’s vest for myself.  It’s similar to the men’s vest but not as complicated.  It’s not lined and the facings are a bit different.  [Edit: I forgot to say why this is a Victorian style vest.  Many women’s garments back then had darts in the front and the back was always princess seams.  This is how this vest is constructed.]

Here are a couple photos of it being laid out.  If you’re new, the best way to cut out stuff is to lay out the pattern, weight it all around, trace around it with chalk/china marker/pen, remove the pattern, then cut out the fabric, cutting off the lines.  Yes, cut off the lines because when you trace the pattern, you add a very small amount, the thickness of the line, and if you don’t cut it off, you add that much all around every piece.

Pattern piece weighted and traced

Detail of laying out and tracing

After you cut out the interfacing, attach it to the facing pieces.  If you want to use sew-in interfacing, you would baste the interfacing and fabric together around the edges, 1/8 to 1/4″ from the edges.  I prefer to use that fusible tricot (knit) kind.  I never have problems with it like I’ve had with the other fusible kind.  If it ends up that the fabric and interfacing don’t exactly match when you’re basting or fusing them together, which sometimes happens when you cut them out, do the best you can in regards to the edge that will be sewn to the neckline/CF/armscye/whatever.  Trim the interfacing if it hangs over the edge but don’t trim the fabric.

The interfacing has been fused to the facings

Since I made this particular vest in Victorian style, I made the fronts with darts (1 piece) and the back princess seams (multiple pieces).  I draft the pattern and pressed the darts so the vertical ones go toward the CF and the horizontal bust dart goes downward.

The darts have been sewn and pressed

Sew the center back, center side back, and side back pieces together with a 3/8″ seam allowance (standard for most seams, use this with the shoulders and side seams).  You will see that I sewed them with the sewing machine then neatened the edges with the overlock.

Back seams from the wrong side

Back seams from the right side

After you have pressed the darts and back seams, join the fronts and back at the shoulders.

Shoulder seams

Press them, sew the side seams, and press them, too.

Side seam sewn

Next, with right sides together, sew the facings to the neckline/CF and the armsyces (armholes).  Use a 1/4″ seam allowance.  Clip all the curves by snipping into the seam allowance to but not through the seam.  Pull the seam allowance toward the facings and understitch the facings 1/16 to 1/8″ away from the seam.  Turn the facings to the inside of the vest and press them.  If necessary, take the edges of the facings to a seam allowance to keep them from working their way to the outside.  The buttons and buttonholes will keep the CF from turning the wrong way.

At the bottom of the CF facings, stop at the point matching the whole width of the hem allowance.  Pivot and sew to the outer edge of the facing.  Clip, turn, and press.

All of this is in the photos below.

The facings have been attached to the vest

One of the armscye facings has been clipped and understitched

Facings understitched and turned to the inside of the vest

Turn at amount of hem allowance and stitch to edge of facing

Clip that corner

Turn to the inside and press it and the hem up the amount of the allowance

Press the vest hem under another time and stitch it just to the edge of the facing

The last things to do are to put in the buttonholes, sew on the buttons, and give the vest a final pressing.  Make sure you do a sample buttonhole first to make sure the button will fit through it.  Most of the time, mine turn out fine, but sometimes if the button is thicker or rounded, you need extra length.  If it’s very thin, you don’t need as much.

If you can find one of these tools (I have no idea what the name is), use it to mark buttons, buttonholes, and other things that need to be evenly spaced. The top section has stuff for buttons and buttonholes.

The buttonholes are spaced and marked with pins

Buttonholes and markings for the buttons

After you put in the buttonholes, slit them open (we always use a seam ripper), then press them.  Matching up the center fronts, lay the buttonholes over the other side.  Using a pen, pencil, chalk pencil, whatever, mark the button spacing through the buttonholes so they will match.  Sew on the buttons.  Press, especially if you’ve gotten it really wrinkled during the sewing process.

The completed garment:

Vest front

Vest back

[Edit: I want you to see in the photo of the front that the back facing isn’t shaped right.  Not at the neckline, but below it.  Do you see how you can see the wrong side of the fabric under the back facing?  The facing should be shaped so it falls below the front neckline so you can’t see the wrong side of the back.]  As soon as I get someone to take some photos of me, I’ll show what it looks like on a body.  (That’s one of my cats, Yaffah, on the chair in the background.)

Advertisements

Leave a comment

Filed under Garments

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s